RESEARCH ARTICLE


Asphalt Binder Performance Grading for the Republic of Yemen Based on Superpave Asphalt Mix-Design



Ghassan M. Ali Hussain1, Mohammed A.G. Abdulaziz2, Zheng N. Xiang3, Mohammed A. Al-Hammadi2, *
1 School of the Highway, Chang’an University, Xi’an 710064, Shaanxi, China
2 School of Civil Engineering, Chang’an University, Xi’an, 710064, Shaanxi, China
3 Key Laboratory for Special Area Highway Engineering of the Ministry of Education, Chang’an University, Xi’an, 710064, Shaanxi, China


Article Metrics

CrossRef Citations:
2
Total Statistics:

Full-Text HTML Views: 1205
Abstract HTML Views: 377
PDF Downloads: 305
Total Views/Downloads: 1887
Unique Statistics:

Full-Text HTML Views: 740
Abstract HTML Views: 267
PDF Downloads: 237
Total Views/Downloads: 1244



Creative Commons License
© 2020 Ali Hussain et al.

open-access license: This is an open access article distributed under the terms of the Creative Commons Attribution 4.0 International Public License (CC-BY 4.0), a copy of which is available at: https://creativecommons.org/licenses/by/4.0/legalcode. This license permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

* Address correspondence to this author at the School of Civil Engineering, Chang’an University, Xi’an 710061, China, Tel: 008615529582720; E-mail: eng.mohammed907@gmail.com


Abstract

Background:

The asphalt binder is considered a temperature-sensitive viscoelastic material. Temperature can cause some common distress of asphalt pavement, such as rutting (permanent deformation), which correlated with high-temperature environments, and thermal cracking, which correlated with low-temperature environments.

Objective:

This study aimed to establish asphalt binder Performance Grades (PGs) in the Yemeni region to ensure that the asphalt pavement design can effectively resist the distresses of rutting and cracking that occurred due to seasonal temperature changes.

Methods:

In order to determine the performance grades, the temperature zoning was performed by obtaining the last 10 years temperature data of 19 cities in Yemen gathered by the Yemeni Meteorological Authority. The collected data were analyzed based on the trend and statistical reliability. Three air-pavement temperature prediction models of Superpave, LTPP, and Oman model were used to predict air pavement temperatures. The local performance grades were computed using reliability levels of 50% and 98%. Since the dependent variables of latitude in the Superpave equation can more reflect the geographical locations of Yemeni regions rather than the other models, this study strongly approved the SHARP Superpave model to be used to determine the performance grades.

Results:

Based on the Superpave model with reliability analyses, performance grade maps were drawn. The most common performance grades recommended in this study for low traffic volume roads were PG64-10, and PG52-10.

Conclusion:

The findings of this study are highly significant and provide valuable decision support for pavement management and improve the transportation system in the Republic of Yemen.

Keywords: Asphalt binder, Performance grade, Superpave, Reliability analysis, Asphalt paving, Yemen.



1. INTRODUCTION

The transportation sector with its various branches is considered an important component of the infrastructure of the Yemeni economy due to its impact on other economic sectors such as the industrial sector, the trading sector, and the tourism sector. Based on the official statistics 2010, the total length of the road network system in the Republic of Yemen was 34,447.1 km, of which 16347.1 km are paved, and 18,100 km are unpaved roads. From 2005 to 2010, the growth rate of asphalt roads reached to 43.46%. The asphalt binder is a temperature-sensitive viscoelastic material; the temperature can cause some common distress of asphalt pavement [1]. Due to the viscoelastic material property, asphalt pavement is susceptible to rutting at high temperatures and subject to cracking due to shrinkage of the binder at low temperatures [2]. Establishing asphalt pavement binder quality standards is a prerequisite for the new highway construction and quality enhancement for the existing asphalt pavements in Yemen. The asphalt binder selection system currently used in Yemen is a penetration grading. The penetration test has been used to determine only one grade of 60-70. Since the test conducted at a single temperature of 25 0°C, it is hard to evaluate asphalt binder rheology properties at low and high temperatures and to determine the temperatures of mixing and compaction of the asphalt that the Superpave PG system can provide. Therefore, it is necessary to analyze the trends of climate data for minimum and maximum temperatures of cities in Yemen and determine asphalt binder grades via predicting the possible changes in temperatures through the statistical reliability techniques.

On such bases, this study aimed to determine the acceptable asphalt binder Performance Grades (PGs) in the Republic of Yemen based on the historic collected air temperature data to predict high and low asphalt pavement temperatures. The study also determined the asphalt binder performance grading maps with 98% and 50% reliability levels. Finally, the most common performance grades were proposed for the Yemeni region. The finding of this study would expand the relevant literature to determine the scientific developments in the field. Moreover, this study could also certainly clarify further research to be developed and conducted on pavement performance at a wide range of climate conditions.

2. BACKGROUND

From October 1987 to March 1993, the US Congress funded a five years program with $ 150 million to develop a new method for testing and designing asphalt materials and enhancing the durability, safety, effectiveness, and highways productivity system in the US [3]. This program was named the highway strategy research program (SHARP). SHARP established the Long-Term Pavement Monitoring Program (LTPP) in 1987 to support an extensive pavement performance analysis, thereby improving engineering tools for designing, managing, and constructing pavements [4].

The Seasonal Monitoring Program (SMP) was proposed in 1991 as a component of LTPP to check and assess the influences of temperature and moisture fluctuations on the performance of pavements and verify the existing models which developed to select the proper asphalt binder based on the SMP data. The minimum air temperature is used as an alternative to the lowest pavement temperature in the actual binder specification, while the LTPP data verify that the low pavement temperature cannot be lower than the lowest air temperature [5].

Based on the initial SHARP testing and SMP data, many pavement temperature approaches were properly established in order to select the proper asphalt binder PGs [6]. Based on the theory of heat and energy transfer, Solaimanian and Kennedy [7, 8] developed an analytical approach, as well as Shao et al. [9]. Proposed a procedure to estimate pavement temperatures. Other researchers [10, 11] developed a regression approach based on collected data sets. Based on the heat transfer approaches given in Solaimanian and Kennedy [12, 13], a simulation model was proposed to determine the pavement temperatures during the summer.

Between 1994 and 1997, two studies were conducted in two different regions by Al-Abdul Wahhab et al. [14, 15]. The first study was manually carried out in Saudi Arabia to measure pavement temperatures in various pavement sections. This study showed that the maximum pavement temperatures ranged from 3 to 72°C in arid environments and from 4 to 65°C in coastal areas. The second study was conducted for the entire Gulf area and suggested five performance graded binder zones. The study also recommended that the currently used asphalt binders should be modified to accommodate the proposed grade.

In 2005, Hassan et al. conducted an extensive two-year study in Oman to develop a temperature model for asphalt pavement [16]. In this study, a monitoring station was set up to measure air and road pavement temperatures. The collected data were analyzed, and a linear regression model was obtained to predict high and low pavement temperatures. Hassan et al. were further improved the above model [17], based on collecting more temperature databases. This study used the Oman model and compared it with the other two models to predict the asphalt binder Performance Grades (PGs) in Yemen because Oman and Yemen have a common border with each other. Therefore, the temperature in Oman is close to those in Yemen.

2.1. Temperature Grade

According to the SUPERPAVE system, the asphalt binder is determined based on the highest and lowest pavement design temperature, where the asphalt binder is expected to serve. The requirements of binder physical properties still the same, but the temperature differs from one binder to another at which the binders accomplish its properties with corresponding to the highest and lowest pavement design temperature. For instance, a binder graded as PG64-10 means that the binder should meet the desired properties, up to a maximum pavement temperature with a value of 64°C and a minimum pavement temperature with a value of -10°C

Table 1 represents the conventional binder grades as stipulated by SUPERPAVE specifications. The maximum temperature of 58°C has a similar low temperature of -16, -22, -28, -34-40°C resulting in PG58-16, PG58-22, PG58-28, PG58-34, and PG58-40. The performance grades are not limited to those provided in Table 1, and it is possible to obtain PG58-10.

Table 1. Binder grades in accordance with SUPERPAVE specifications [4].
High-Temperature Grade °C Low-Temperature Grade °C
PG46 ˗34, -40, -46
PG52 -10, -16, -22, -28, -34, -40, -46
PG58 -16, -22, -28, -34, -40
PG64 -10, -16, -22, -28, -34, -40
PG70 -10, -16, -22, -28, -34, -40
PG76 -10, -16, -22, -28, -34
PG82 -10, -16, -22, -28, -34, -40

2.2. Selection of PG Based on Traffic Volume and Speed

The selection of asphalt binder in accordance with SUPERPAVE is based on an assumed traffic volume, including the design of the fast-transient load number. For different traffic conditions, the loading speed has supplemental effects on the pavement’s ability to withstand rutting (permanent deformation) under high-temperature conditions. Therefore, binder grades must increase with one grade for the high pavement temperature design, which is equal to 6 °C. One level shift is typically used for slow-moving, while two grades are used for standing design load conditions, as shown in Table 2.

For a very high number of heavy traffic loads, there is an additional shift. It is recommended that the design lane traffic is expected to exceed 10 million Equivalent Single Axle Load (ESAL), defined as an 18,000 pound (KN) four-tire dual axle. In addition, if the designed traffic is expected to be between (10-30) million ESAL, may consider shifting one high-temperature asphalt binder grade that is higher than the once selected based on climate condition. However, If the design traffic is expected to exceed 30 million ESAL, then the binder should be shifted with one grade higher [18]. Table 2 presents Super-pave high-temperature design grade adjustment specifications based on traffic and speed conditions.

3. RESEARCH METHODOLOGY

In order to achieve the objectives of this study and determine the asphalt binder PGs, several procedures were applied as follows:

(1) The air temperature data collected for this study covered approximately 10 years (2006-2015) for 19 Yemeni cities representing all the unique areas of Yemen. All stations are presented in Table 3. For every single station, the following parameters were extracted from the station's database to be used as preliminary data, the maximum daily temperature selected as the maximum temperature recording for 24 hours, the minimum daily temperature selected as the minimum temperature recording for 24 hours and the latitude for each of nineteen specific weather stations.

Table 2. Adjustment to the high-temperature grade of binder based on traffic level and traffic speed [5].
Design ESALs
    (Million)
Adjustment to Binder PG Grade
Traffic Load Rate
Standing (Avg.
Speed < 20 Km/hr
Slow (Avg.
Speed 20 to 70
Km/hr
Standard (Avg. Speed › 70 km/hr
< 0.3 - - -
0.3 to < 3 2 1 -
3 to <10 2 1 -
10 to < 30 2 1 -
> 30 2 1 1
Table 3. Summary of max and min air temperatures recorded at weather stations.
Cities in Yemen     Max. Air Temperature (°C) Min. Air Temperature (°C)
Highest Mean St. dev. Lowest Mean St. dev
Sana'a 28.4 27.05 1.05 -1 0.91 1.04
Amran 28.4 26.39 1.28 1 1.97 0.74
Dhale 31.3 29.27 1.61 7.8 8.92 0.76
Al Hudaydah 40.3 39.1 0.96 20.1 21.29 0.84
AL Jawf 35.3 33.53 1.46 12.1 13.09 0.67
AL Mahwit 29.1 27.765 0.98 9.1 10.69 0.89
Dhamar 26.8 24.83 1.20 -2.5 0.38 1.47
Ibb 30.4 28.62 1.20 3.5 6.35 2.02
Ma’rib 37.2 36.29 0.77 11.7 12.60 0.76
Sadah 30.1 28.56 0.82 5.9 7.12 1.12
Taiz 33.8 32.455 1.19 11.1 11.93 0.61
Aden 39.7 38.01 1.05 19.85 21.35 1.27
Abyan 37.7 37.08 0.67 19.6 20.44 0.83
Al Mahrah 37.8 37.05 0.51 20.1 21.20 0.89
Hadhramaut 38.7 37.97 0.57 21.9 22.70 0.63
Socotra 33.3 31.08 1.15 16.1 18.33 1.35
Lahij 39.2 38.17 0.78 20.9 22.12 0.84
Shabwah 38.5 37.195 0.54 21.3 22.39 0.79
Hajjah 31.3 30.17 0.70 4.3 6.26 0.91

(2) Yemen was divided into different climatic zones based on the highest and lowest pavement temperature. Nineteen cities across Yemen were chosen to be used in this paper. At each year of the study period (2006-2015), the hottest and lowest temperature is identified, and the average maximum air temperature for consecutive seven-days and the minimum air temperature for 1-day is calculated.

(3) After determining the maximum and minimum air temperature of each year, the mean and standard deviation were computed to determine the high and low temperature at 98% and 50% reliability level by using three models of SHARP, LTPP, and Oman model. Oman model was used due to the common border between Yemen and Oman. Therefore, the weather is almost the same . According to the SUPERPAVE, reliability can be defined as the percentage of probability in a single year when the actual temperature (minimum temperature of one day or high temperature of seven-days) will not exceed the degree of design temperature. Reliability with a higher percent means lower risk and mainly depends on traffic volume, binder cost as well as the functional class of the road. 98%-reliability must be used for heavy traffic, while 50% for summer.

(4) The temperature trends analyzed to determine whether temperature varies could be predicted.

(5) Use the hottest and coldest pavement temperatures to determine a reliable asphalt binder PG through a temperature change prediction model or statistical analysis.

(6) Showing the asphalt binder PGs maps of Yemen with the reliability of 50% and 98% based on the SHARP model.

(7) Proposed the most common asphalt binder grades (PGs) for Yemen

3.1. Analysis of Air Temperature Data

Firstly, the collected data from 19 cities were finalized to get a clear picture of temperature changes in every single city. After that, the maximum and minimum air temperatures collected were recorded in each city. The mean and standard deviation of the maximum and minimum temperatures in each city for different years were also recorded, as presented in Table 3. The highest temperature varies between 26.8°C and 40.3°C, while the lowest temperature varies between -2.5°C and 21.9 °C

3.1.1. Average 7-days Maximum and Minimum Temperature

In this paper, the average 7-days maximum temperature and minimum temperature in 19 regions of Yemen during 10 years period from 2006 to 2015 were filtered from the collected temperature database. Fig. (1) shows the average 7-days maximum air temperatures during the summertime of 19 cities in Yemen over the past 10 years, the highest temperature was 39.1°C in Al Hudaydah city, and the lowest temperature was 26.39°C in Amran city.

The average minimum air temperature for most of the cities in Yemen in the past 10 years was shown in Fig. (2); only two cities (Dhamar and Sana’a) hit the lowest temperature of -2.5°C, and -1°C, respectively, while the highest of 21.9°C in Hadhramaut. As indicated in Figs. (1 and 2), the results show that it is warm in the cities located along the coastline plus some cities in the highland plateau, and it is cold in the mountain highlands region. The temperature difference between the minimum and maximum is about 13.5°C during summertime and 24.4°C during wintertime. This large seasonal temperature difference in winter indicates that different asphalt binder for low temperature cracking resistance levels used, if the low temperature falls below zero degrees, but if the value ranged between -2.5°C and 21.9°C, for Yemeni region, the predicted min pavement temperature is much higher than the min required for a PG grade, therefore, the low temperature implemented for all PG grade is -10°C.

3.1.2. Trend Analysis of Temperature Variation

Fig. (3) shows the temperature variations of Al Hudaydah and Amran. The two cities reach the average maximum and minimum air temperatures, respectively, in summer. The linear regression analysis of the overall temperature trend showed that the average temperature of Al Hudaydah increased by 0.04°C and Amran decreases by -0.13°C each year. Fig (4) shows the temperature variations in Dhamar and Hadhramaut, in which two cities reach the average maximum and minimum air temperatures, respectively, in winter. According to the results of linear regression analysis, it can be found that the annual average temperature of Dhamar increases by 0.22°C and Hadhramaut decreases 0.06°C.

Fig. (1). Average 7-days maximum air temperature for 10 years.

Fig. (2). Average minimum air temperature for 10 years.

Fig. (3). Variation of max. Air temperature for 10 years in Al-Hudaydah and Amran city, Yemen.

The linear regression models of average 7-days maximum and minimum air temperature vary, as shown in Figs. (3 and 4), while the linear trends of remaining cities also vary are illustrated in Figs. (5 and 6) to verify the average maximum and minimum air temperature increases or decreases during the past 10 years by the value of -0.03 and 0.07, respectively. It is observed that during the summer, Aden experienced the largest increase in the average 7-days maximum temperature, while in Dhamar, the temperatures tended to drop. In winter, Sana’a and Ibb experienced the largest drop and increment, respectively, in the minimum air temperature, as shown in Figs. (5 and 6).

Fig. (4). Variation of min. Air temperature for 10 years in Dhamar and Hadhramaut city, Yemen.

Fig. (5). Average 7-days max. Air temperature increase for 10 years in Yemen cities.

Fig. 6. Average min. Air temperature increase for 10 years in Yemen cities.

As shown in Fig. (3) through Fig. (6), Yemenis’ seasonal maximum and minimum air temperatures over the past 10 years have fluctuated unpredictably, rising and falling repeatedly, which makes it difficult to develop a regression analysis formula and then predict the future pavement temperature. Therefore, it is considered to use the mean and standard deviations of air temperature in the past for Yemen to predict air temperature using statistical reliability techniques.

3.2. Prediction of Pavement Temperature

Several models and algorithms could be used to compute the high temperature of pavement at any depth [17]. In this paper, the common depth of 20 mm beneath the pavement surface is computed for the high pavement temperature, while the low pavement temperature is computed at the pavement surface. The Superpave asphalt performance grade is determined based on actual asphalt pavement temperatures. Most countries have determined such models based on the air and pavement temperature. These models are used for asphalt mix design. Since it is difficult to gather the actual pavement temperatures from field surveys at specific locations in Yemen, this study utilized relationship equations for countries with a similar climate to Yemen, such as Oman, besides SHARP and LTPP models.

3.2.1. Air-pavement Temperature based on SHARP and LTPP Model

The relationship equations between the highest pavement temperature at 20 mm depth below the pavement surface and the average 7-days maximum air temperature using SHARP Superpave and LTPP system is shown as in Eq. (1) and Eq. (2), respectively. It is found that the relationship between air and pavement temperature varies by the latitude, as presented in Eq. (1).

(1)
(2)

Where

T20mm = High pavement temperature at a depth of 20 mm,°C

Tair = the highest average air temperature of 7-days,°C

Lat = the weather station’s latitude in degree

Tpav = Hight pavement temperature at depth H from the surface,°C

H = Pavement depth from the surface, mm

While the minimum pavement design temperature on the asphalt pavement surface is equal to the one-day low air temperature because the air temperature is approximately the same as the pavement surface temperature. Eq. (3) and (4) present the model established under the SHARP and LTPP program, respectively.

(3)
(4)

Where

Tmin = Minimum pavement temperature,°C

Tair = the low air temperature,°C

Lat = the weather station’s latitude in degree

H = Pavement depth from the surface, mm

3.2.2. Air-pavement Temperature Based on Oman Model

Oman model was firstly developed [16] and further enhanced [19] after gathering more weather data. The final Oman model for the high and the low pavement temperature is expressed, as shown in Eqs. (5) and (6), respectively.

(5)
(6)

Where

T20mm = High pavement temperature at a depth of 20mm,°C

Tmin = Minimum pavement temperature,°C

Tair = the highest average air temperature of 7-days,°C

3.3 Comparison of three prediction models

As illustrated in Fig. (7) through Fig. (10), the Oman relationship model was graphically compared with other models of LTPP and SHARP in terms of the average 7-days maximum and minimum pavement temperatures using the equality lines. The three models were used to compare the maximum and minimum pavement temperatures of 19 cities in Yemen over the past 10 years.

By comparing the three models, the Oman model is in good agreement with the maximum pavement temperature of SHARP and LTPP models, indicating that the pavement temperature obtained by Oman model is lower than that obtained by SHARP and LTPP models. The reason behind the large difference in pavement high temperature could be due to the poor fitting quality of Oman model. However, the maximum pavement temperature obtained using SHARP's equations exhibited slightly higher values compared with that obtained using LTPP's equations, as shown in Figs. (7 and 9). On the other hand, for the minimum temperature, there is no good fit and the graph shows large variations between Oman model and the other two models of SHARP and LTPP, as presented in Figs. (8 and 10). In this paper, the SHARP’s model was adopted to compute the pavement temperatures of the asphalt binder performance level in Yemen, due to the fact that, this model used the dependent variable of latitude that can better reflect the geographical locations of the Yemeni region rather than other models.

Fig. (7). Comparison of max. Pavement temperature between LTPP and Oman model.

Fig. (8). Comparison of min. pavement temperature between LTPP and Oman model.

Fig. (9). Comparison of max. Pavement temperature between SHARP and Oman model.

Fig. (10). Comparison of min. pavement temperature between SHARP and Oman model.

4. RESULTS AND DISCUSSION

4.1. Temperature Zoning for Developing PG Map

4.1.1. Reliability Analysis Approach

In this paper, the use of the maximum and minimum air temperatures attributes to the mean of the average 7-days maximum temperature and the mean of the minimum temperature, respectively, recorded at each weather station. These two means were computed from (n) observations obtained in the (n) years at each station, as presented in Table 4 under the reliability level of 50%. The reliability level of 95% and 98% for the max and min air temperature was calculated based on the standard deviations for the reliability of 50%. In detail, the max temperature at the reliability of 95% is determined as the combination of the mean temperature at the reliability of 50% plus 1.65 multiply by the standard deviation. At the same time, the max temperature at the reliability of 98% is calculated as the combination of the mean temperature at the reliability of 50%, adding 2.055 multiply by the standard deviation. On the other hand, the min temperatures at the reliability of 95% and 98% were calculated in the same way, except that reduction is made from the mean temperature rather than by addition at the reliability of 50%.

The asphalt binder PGs were computed based on the two-reliability level of 50% and 98% considered in this study rather than using the reliability of 95% since the values of 95% and 98% reliability levels were almost the same. PGs with 50% reliability is much chapter than those of 98% reliability, but it is more likely prone to temperature-causing pavement damage. Based on the pavement design method of the Superpave implemented by most states in the US. Through using the cost-benefit analysis, the asphalt binder PGs were determined with the reliability of 98%. However, due to the economic situation in Yemen, PGs with the reliability of 50% might be used in the low-traffic volume road.

4.1.2. Air Temperature Reliability Analysis Results

The analysis results of 50% and 98% reliability at the average of 7-days maximum and minimum air temperatures are shown in Table 4. The asphalt pavement temperatures were determined by converting the average 7-days max and min air temperature using the above mentioned three models (Eqs. 1 to 6) and discussed earlier in the “Prediction of Pavement Temperature” section, then the obtained results presented in Table 5.

4.1.3. Analysis Result of 50% and 98% Reliability

Table 6 shows a comparison of the asphalt binder grades PGs computed by using three models of SHARP, LTTP, and Oman model of average 7-day maximum and minimum pavement temperatures for the specified cities in Yemen at 50%, and 98% reliability.

The results obtained from the SHARP and LTPP model at 50% reliability analysis indicated that the Yemeni region requires three different asphalt binder PGs: PG52-10 (1), PG58-16 (2), and PG 64-10(3), as well as Oman model, requires three different asphalt binder PGs. The 98% reliability analysis results were also similar to those of the 50% reliability analysis, which indicated that the Yemeni region requires three different PGs. However, the pavement temperatures predicted by the SHARP model were relatively higher than those predicted by the other models, especially for maximum pavement temperatures. Moreover, the results showed that the Oman model has a lower pavement temperature than SHARP and LTPP models. The reason for the large difference in high temperatures can be attributed to the low quality of fit of the Oman model. Due to that, the dependent variables of latitude in the Superpave equation can more reflect the geographical locations of Yemeni regions rather than the other models. The SHARP model found out to be more practical than other models from the perspective of the required binder PGs in Yemen. The findings of this study are consistent with those of the other overseas studies. Hassan et al. [ 19 ] and Balushi et al. [ 20 ] tested the SHARP and LTPP models against actual measurements of air and pavement temperatures and concluded that the LTPP model produced closer results to actual temperatures; the authors believe that the LTPP and SHARP models would be more appropriate to be used while the Oman model showed the least quality.

4.1.4. Proposed PG Map

In order to prevent pavement damage due to seasonal temperature variations (which may expose the pavement), the asphalt binder PGs determined through statistical reliability analysis [21].

As shown in Figs. (11 and 12), the asphalt binder PGs map of the Yemeni region was derived from the SHARP model, with a reliability level of 50%, and 98%, respectively. In this study, the most common PGs recommended for low volume roads and heavy traffic volume at 50% and 98% reliability level, respectively, are PG52-10, PG58-16, and PG64-10 (Table 6).

4.2. Traffic Speed and Loading Effect in the Selection of Performance Grade

Table 7 shows the selected PGs that should be shifted up using the SHARP model with a 98% reliability level after traffic adjustments for the asphalt binder grades in accordance with traffic speed and loading rate. For example, PG with slow traffic speed should be shifted with one grade from the selected performance grade.

Fig. (11). Generated map of asphalt binder PGs for Yemen based on SHARP model with 98% reliability.

Table 4. Max and min air temperatures at different reliability levels.
Cities in Yemen Lat. 7-days Max Air Temperature (°C) Min Air Temperature (°C)
Reliability Reliability
50% 95% 98% 50% 95% 98%
Mean St. dev Mean Mean Mean St. dev Mean Mean
Sana'a 15.35 27.05 1.05 28.78 29.21 0.91 1.04 -0.81 -1.24
Amran 15.25 26.39 1.28 28.50 29.02 1.97 0.74 0.75 0.45
Dhale 13.70 29.27 1.61 31.92 32.57 8.92 0.76 7.67 7.36
Al Hudaydah 14.80 39.10 0.96 40.69 41.08 21.29 0.84 19.91 19.57
AL Jawf 13.10 33.53 1.46 35.94 36.53 13.09 0.67 11.99 11.72
AL Mahwit 15.28 27.77 0.98 29.39 29.78 10.69 0.89 9.23 8.87
Dhamar 14.55 24.83 1.20 26.81 27.30 0.38 1.47 -2.05 -2.64
Ibb 13.97 28.62 1.20 30.60 31.08 6.35 2.02 3.01 2.19
Ma’rib 15.46 36.29 0.77 37.55 37.87 12.60 0.76 11.35 11.04
Sadah 16.93 28.56 0.82 29.92 30.25 7.12 1.12 5.27 4.81
Taiz 13.58 32.46 1.19 34.43 34.91 11.93 0.61 10.92 10.67
Aden 12.81 38.01 1.05 39.75 40.17 21.35 1.27 19.25 18.73
Abyan 13.88 37.08 0.67 38.18 38.45 20.44 0.83 19.07 18.73
Al Mahrah 16.21 37.05 0.51 37.88 38.09 21.20 0.89 19.73 19.37
Hadhramaut 14.53 37.97 0.57 38.91 39.14 22.70 0.63 21.67 21.41
Socotra 12.47 31.08 1.15 32.98 33.45 18.33 1.35 16.10 15.56
Lahij 16.12 38.17 0.78 39.45 39.77 22.12 0.84 20.73 20.39
Shabwah 14.32 37.20 0.54 38.09 38.30 22.39 0.79 21.09 20.78
Hajjah 15.25 30.17 0.70 31.33 31.62 6.26 0.91 4.76 4.39
Fig. (12). Generated map of asphalt binder PGs for Yemen based on SHARP model with 50% reliability.

Table 5. Comparison between pavement temperature using LTPP, SHARP, and Oman model for different cities in Yemen.
Cities in Yemen     LTTP Model     SHARP Model Oman Model
Reliability
    of 50%
Reliability
    of 98%
Reliability
    of 50%
Reliability
    of 98%
Reliability
    of 50%
Reliability
    of 98%
Max Min Max Min Max Min Max Min Max Min Max Min
Sana'a 49.80 8.50 51.48 2.38 50.47 2.48 52.53 0.64 39.13 0.16 41.87 -2.18
Amran 49.29 9.28 51.34 3.74 49.84 3.39 52.35 2.09 38.29 1.32 41.63 -0.33
Dhale 51.65 14.46 54.23 8.89 52.52 9.36 55.67 8.03 41.95 8.89 46.15 7.20
Al Hudaydah 59.24 23.24 60.79 17.51 61.95 19.99 63.85 18.51 54.44 22.38 56.96 20.50
Al Jawf 55.01 17.53 57.35 12.12 56.55 12.94 59.41 11.77 47.36 13.44 51.17 11.95
Al Mahwit 50.36 15.55 51.94 9.74 51.15 10.88 53.08 9.32 40.04 10.82 42.60 8.84
Dhamar 48.13 8.22 50.05 1.21 48.32 2.03 50.68 -0.57 36.30 -0.41 39.44 -3.71
Ibb 51.13 12.58 53.05 4.34 51.91 7.15 54.26 3.58 41.12 6.09 44.25 1.56
Ma’rib 57.00 16.91 58.23 11.33 59.30 12.52 60.80 11.18 50.87 12.91 52.87 11.21
Sadah 50.85 12.77 52.17 6.49 51.96 7.82 53.57 5.83 41.05 6.93 43.19 4.42
Taiz 54.14 16.64 56.06 11.33 55.55 11.95 57.89 10.87 46.00 12.17 49.12 10.81
Aden 58.53 23.50 60.22 16.92 60.80 20.04 62.87 17.79 53.06 22.44 55.81 19.59
Abyan 57.73 22.74 58.80 17.02 59.98 19.26 61.29 17.79 51.87 21.45 53.62 19.59
Al Mahrah 57.53 23.00 58.34 17.18 60.05 19.91 61.04 18.34 51.84 22.28 53.16 20.28
Hadhramaut 58.38 24.29 59.30 18.95 60.86 21.20 61.98 20.10 53.01 23.92 54.50 22.51
Socotra 53.14 21.36 54.99 14.62 54.16 17.45 56.43 15.06 44.25 19.15 47.26 16.13
Lahij 58.41 23.68 59.66 17.94 61.11 20.70 62.64 19.21 53.26 23.28 55.29 21.40
Shabwah 57.79 24.09 58.66 18.46 60.11 20.93 61.17 19.55 52.02 23.58 53.43 21.82
Hajjah 52.24 12.37 53.37 6.50 53.45 7.08 54.83 5.47 43.09 5.99 44.93 3.96
Table 6. Comparison of asphalt binder PG using LTPP, SHARP, and Oman model at 50%, 98% reliability.
Cities in Yemen     Selected PG Binder Grade
LTTP SHARP Oman Model
50%
    Reliability
98% Reliability 50% Reliability 98% Reliability 50% Reliability 98% Reliability
Sana'a PG52-10 PG52-10 PG52-10 PG58-16 PG46-10 PG46-10
Amran PG52-10 PG52-10 PG52-10 PG58-16 PG46-10 PG46-10
Dhale PG52-10 PG58-16 PG58-16 PG58-16 PG46-10 PG52-10
Al Hudaydah PG64-10 PG64-10 PG64-10 PG64-10 PG58-16 PG58-16
AL Jawf PG58-16 PG58-16 PG58-16 PG64-10 PG52-10 PG52-10
AL Mahwit PG52-10 PG52-10 PG52-10 PG58-16 PG46-10 PG46-10
Dhamar PG52-10 PG52-10 PG52-10 PG52-10 PG46-10 PG46-10
Ibb PG52-10 PG58-16 PG52-10 PG58-16 PG46-10 PG46-10
Ma’rib PG58-16 PG64-10 PG64-10 PG64-10 PG52-10 PG58-16
Sadah PG52-10 PG58-16 PG52-10 PG58-16 PG46-10 PG46-10
Taiz PG58-16 PG58-16 PG58-16 PG58-16 PG46-10 PG52-10
Aden PG64-10 PG64-10 PG64-10 PG64-10 PG58-16 PG58-16
Abyan PG58-16 PG64-10 PG64-10 PG64-10 PG52-10 PG58-16
Al Mahrah PG58-16 PG64-10 PG64-10 PG64-10 PG52-10 PG58-16
Hadhramaut PG64-10 PG64-10 PG64-10 PG64-10 PG58-16 PG58-16
Socotra PG58-16 PG58-16 PG58-16 PG58-16 PG46-10 PG52-10
Lahij PG64-10 PG64-10 PG64-10 PG64-10 PG58-16 PG58-16
Shabwah PG58-16 PG64-10 PG64-10 PG64-10 PG58-16 PG58-16
Hajjah PG58-16 PG58-16 PG58-16 PG58-16 PG46-10 PG46-10
Table 7. PGs for 98% reliability in SHARP model after traffic adjustments in Yemen.
Selected PGs Design ESALs (Million) Adjustment to Binder PG Grade
Traffic Load Rate
Standing Slow Standard
52-10 < 0.3 52-10 52-10 52-10
0.3 to < 3 64-10 58-10 52-10
3 to <10 64-10 58-10 52-10
10 to < 30 64-10 58-10 52-10
> 30 64-10 58-10 58-10
58-16 < 0.3 58-16 58-16 58-16
0.3 to < 3 70-16 64-16 58-16
3 to <10 70-16 64-16 58-16
10 to < 30 70-16 64-16 58-16
> 30 70-16 64-16 64-16
64-10 < 0.3 64-10 64-10 64-10
0.3 to < 3 76-10 70-10 64-10
3 to <10 76-10 70-10 64-10
10 to < 30 76-10 70-10 64-10
> 30 76-10 70-10 70-10

CONCLUSION

The main objective of this paper is to determine the asphalt binder PGs for the Yemeni region based on comprehensive collected data of the existing meteorological weather stations. These data were analyzed according to the model developed under three models of SHARP and LTPP and Oman. The findings of this study are summarized, which can be used as the fundamental implementations for the asphalt pavement mix design in Yemeni roads.

  1. Compared with other LTPP and Oman models, the SHARP Superpave model is considered to be more practical and accurate in predicting air pavement temperatures in Yemen.
  2. The performance grade (PG) in Yemen's regions can be divided into three asphalt grades according to the SHARP at 50% and 98% of reliability level, namely, PG64-10(1), PG58-16(2), and PG52-10(3).
  3. The most common performance grades proposed in this study are PG64-10 and PG52-10, which cover most cities in Yemen.
  4. In different cases such as standing, slow, or standard speed, the selected performance grade asphalt binder shifted up by one or two grades based on the traffic volume.

The findings of this study are highly significant and provide valuable decision support for pavement management and the development of local transportation system sustainability and social-economic improvements. This research can become more helpful and interesting if further research would be considered with more stations to be installed in different areas of the country which could enhance the developed models. Field validation of the proposed binder grades would also be recommended.

LIST OF ABBREVIATIONS

PGs  = Performance Grades
UNESCAP  = United Nations Economic and Social Commission for Asia and the Pacific
SHARP  = Highway Strategy Research Program
LTPP  = Long-Term Pavement Monitoring Program
SMP  = Seasonal Monitoring Program
ESAL  = Equivalent Single Axle Load

CONSENT FOR PUBLICATION

Not applicable.

AVAILABILITY OF DATA AND MATERIALS

The data that support the findings of this study are available from the corresponding author, [M.A], upon request.

FUNDING

None.

CONFLICT OF INTEREST

The authors declare no conflict of interest, financial or otherwise.

ACKNOWLEDGEMENTS

Declared none.

REFERENCES

[1] M. Iqbal, A. Hussain, A. Khattak, and K. Ahmad, "Improving the Aging Resistance of Asphalt by Addition of Polyethylene and Sulphur", Civ. Eng. J, vol. 6, no. 5, pp. 1017-1030, 2020.
[2] M. Tausif, S. Bilal, A. Zaidi, N. Ahmad, and M. Sohail, "Influence of Natural Zeolite and Paraffin Wax on Adhesion Strength Between Bitumen and Aggregate", Civ. Eng. J, vol. 6, no. 4, pp. 733-742, 2020.
[3] T. Harman, J. D’Angelo, and J. Bukowski, Superpave asphalt mixture design workshop workbook., Fed. Highw. Adm. Washingt, 2000.
[4] B.K. Diefenderfer, I.L. Al-Qadi, S.D. Reubush, and T.E. Freeman, "Development and validation of a model to predict pavement temperature profile", TRB 2003 Annual Meeting, vol. 21, 2003.
[5] A. Mohseni, LTPP seasonal asphalt concrete (AC) pavement temperature models United States. Federal Highway Administration. Office of Engineering, 1998.
[6] A. Mohseni, and M. Symons, Effect of improved LTPP AC pavement temperature models on SuperPave performance grades, 1998.
[7] A. Mohseni, and M. Symons, Improved AC pavement temperature models from LTPP seasonal data, 1998.
[8] M. Solaimanian, and T.W. Kennedy, "Predicting maximum pavement surface temperature using maximum air temperature and hourly solar radiation", Transp. Res. Rec., p. 1, 1993.
[9] L. Shao, S.W. Park, and Y.R. Kim, "Simplified procedure for prediction of asphalt pavement subsurface temperatures based on heat transfer theories", Transp. Res. Rec., vol. 1568, no. 1, pp. 114-123, 1997.
[10] P.J. Bosscher, H.U. Bahia, S. Thomas, and J.S. Russell, "Relationship between pavement temperature and weather data: Wisconsin field study to verify superpave algorithm", Transp. Res. Rec., vol. 1609, no. 1, pp. 1-11, 1998.
[11] C. Marshall, R. Meier, and M. Welch, "Seasonal temperature effects on flexible pavements in Tennessee", Transp. Res. Rec., vol. 1764, no. 1, pp. 89-96, 2001.
[12] Å. Hermansson, "Simulation model for calculating pavement temperatures including maximum temperature", Transp. Res. Rec., vol. 1699, no. 1, pp. 134-141, 2000.
[13] Å. Hermansson, "Mathematical model for calculation of pavement temperatures: comparison of calculated and measured temperatures", Transp. Res. Rec., vol. 1764, no. 1, pp. 180-188, 2001.
[14] H.I. Al-Abdul Wahhab, and F.A. Balghunaim, "Asphalt pavement temperature related to arid Saudi environment", J. Mater. Civ. Eng., vol. 6, no. 1, pp. 1-14, 1994.
[15] H.I.A-A. Wahhab, I.M. Asi, I.A. Al-Dubabe, and M.F. Ali, "Development of performance-based bitumen specifications for the Gulf countries", Constr. Build. Mater., vol. 11, no. 1, pp. 15-22, 1997.
[16] H.F. Hassan, A.S. Al-Nuaimi, R. Taha, and T.M.A. Jafar, "Development of asphalt pavement temperature models for Oman", J. Eng. Res., vol. 2, no. 1, pp. 32-42, 2005.
[17] M. Minhoto, J. Pais, and P. Pereira, Asphalt pavement temperature prediction, 2006.
[18] A. Institute, Performance graded asphalt binder specification and testing, 2003.
[19] H.F. Hassan, A. Al-Nuaimi, S. Al-Oraimi, and T.M.A. Jafar, "Development of asphalt binder performance grades for Omani climate", Constr. Build. Mater., vol. 22, no. 8, pp. 1684-1690, 2008.
[20] A. Balushi, M. Metwally, and M. H. Al-rashdi, Development of oman performance grade paving map for superpave asphalt mix design.
[21] D.S. Moore, The Basic Practice of Statistic, 3rd editionW.H. Freeman and Co: New York, 2004.